Схема разделов Beeline Smartbox

Приветствую, друзья.
Копошась как-то в логах dmesg обнаружил интересную, на мой взгляд информацию, а именно схему разделов (предствлена ниже):
SPI flash(MX25L12805D/45E) was found at CS0, size 0x1000000
Creating 11 MTD partitions on «flash_bank_1»:
0x000000000000-0x000000020000 : «bootloader»
0x000000020000-0x000000150000 : «kernel_recovery»
0x000000150000-0x0000003a0000 : «fs_recovery»
0x0000003a0000-0x0000003d0000 : «reserved»
0x0000003d0000-0x000000550000 : «kernel»
0x000000550000-0x000000f90000 : «rootfs»
0x000000f90000-0x000000fa0000 : «mac_ip»
0x000000fa0000-0x000000fb0000 : «critical_log»
0x000000fb0000-0x000000fc0000 : «critical_log_backup»
0x000000fc0000-0x000000fe0000 : «xml_config»
0x000000fe0000-0x000001000000 : «xml_config_backup»
usbmon: debugfs is not available

Полный лог ниже

Спойлер

Linux version 2.6.30.9 ([email protected]) (gcc version 4.4.5-1.5.5p4 (GCC) ) #1 Mon Feb 16 13:02:22 CST 2015
console [early0] enabled
CPU revision is: 0000dc02
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Zone PFN ranges:
Normal 0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00004000
On node 0 totalpages: 16384
free_area_init_node: node 0, pgdat 8044a070, node_mem_map 81000000
Normal zone: 128 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 16256 pages, LIFO batch:3
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttyS0,38400 root=/dev/mtdblock5
icache: 64kB/32B, dcache: 32kB/32B, scache: 0kB/0B
NR_IRQS:48
PID hash table entries: 256 (order: 8, 1024 bytes)
console handover: boot [early0] -> real [ttyS0]
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 54744k/65536k available (3228k kernel code, 10724k reserved, 1169k data, 108k init, 0k highmem)
Calibrating delay loop… 657.40 BogoMIPS (lpj=328704)
Mount-cache hash table entries: 512
net_namespace: 756 bytes
NET: Registered protocol family 16
bio: create slab at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
NTFS driver 2.1.29 [Flags: R/W].
fuse init (API version 7.11)
msgmni has been set to 107
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x18002000 (irq = 8) is a 16550A
Driver ‘sd’ needs updating — please use bus_type methods
PPP generic driver version 2.4.2
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
Realtek WLAN driver — version 1.6 (2013-02-21)
wlan_index:0 0, 6,0xb9000000,0xb8b10000,11
=====>>INSIDE rtl8192cd_init_one <<===== PCIE reset (0) Do MDIO_RESET Find Port=0 Device:Vender ID=819110ec vendor_deivce_id=819110ec ####################################################### SKB_BUF_SIZE=2408 MAX_SKB_NUM=480 ####################################################### =====>>EXIT rtl8192cd_init_one <<===== =====>>INSIDE rtl8192cd_init_one <<===== =====>>EXIT rtl8192cd_init_one <<===== =====>>INSIDE rtl8192cd_init_one <<===== =====>>EXIT rtl8192cd_init_one <<===== =====>>INSIDE rtl8192cd_init_one <<===== =====>>EXIT rtl8192cd_init_one <<===== =====>>INSIDE rtl8192cd_init_one <<===== =====>>EXIT rtl8192cd_init_one <<===== =====>>INSIDE rtl8192cd_init_one <<===== =====>>EXIT rtl8192cd_init_one <<===== Probing RTL8186 10/100 NIC-kenel stack size order[3]… chip name: 8196C, chip revid: 0 NOT YET eth0 added. vid=9 Member port 0x1… eth1 added. vid=8 Member port 0x10… eth2 added. vid=9 Member port 0x2… eth3 added. vid=9 Member port 0x4… eth4 added. vid=9 Member port 0x8… eth5 added. vid=9 Member port 0x0… Init priv skb. [peth0] added, mapping to [eth1]… repeater_mode_on_init ———————— SPI INIT ————————- Force into Single IO Mode ———————— |No chipID Sft chipSize blkSize secSize pageSize sdCk opCk chipName | | 0 c22018h 0h 1000000h 10000h 1000h 100h 50 0 MX25L12805D/45E| —————————————————————————- SPI flash(MX25L12805D/45E) was found at CS0, size 0x1000000 Creating 11 MTD partitions on «flash_bank_1»: 0x000000000000-0x000000020000 : «bootloader» 0x000000020000-0x000000150000 : «kernel_recovery» 0x000000150000-0x0000003a0000 : «fs_recovery» 0x0000003a0000-0x0000003d0000 : «reserved» 0x0000003d0000-0x000000550000 : «kernel» 0x000000550000-0x000000f90000 : «rootfs» 0x000000f90000-0x000000fa0000 : «mac_ip» 0x000000fa0000-0x000000fb0000 : «critical_log» 0x000000fb0000-0x000000fc0000 : «critical_log_backup» 0x000000fc0000-0x000000fe0000 : «xml_config» 0x000000fe0000-0x000001000000 : «xml_config_backup» usbmon: debugfs is not available ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver b8021000=10000001 b8021054=200000 reg e0=99 reg e1=ac reg e2=98 reg e3=c1 reg e4=1 reg e5=89 reg e6=98 reg e7=1d reg f0=fc reg f1=8c reg f2=0 reg f3=11 reg f4=fb reg f5=d2 reg f6=0 rtl8652-ehci rtl8652-ehci.0: RTL8652 On-Chip EHCI Host Controller rtl8652-ehci rtl8652-ehci.0: new USB bus registered, assigned bus number 1 read synopsys=0 read synopsys2=0 rtl8652-ehci rtl8652-ehci.0: irq 10, io base 0x18021000 rtl8652-ehci rtl8652-ehci.0: USB 0.0 started, EHCI 1.00 [USB] Device ‘RTL8652 On-Chip EHCI Host Controller rtl8652-ehci.0’is plugged into port 1. usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: RTL8652 On-Chip EHCI Host Controller usb usb1: Manufacturer: Linux 2.6.30.9 ehci_hcd usb usb1: SerialNumber: rtl8652-ehci.0 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver rtl8652-ohci rtl8652-ohci.0: RTL8652 OHCI rtl8652-ohci rtl8652-ohci.0: new USB bus registered, assigned bus number 2 rtl8652-ohci rtl8652-ohci.0: irq 10, io mem 0x18020000 [USB] Device ‘RTL8652 OHCI rtl8652’is plugged into port 2. usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: RTL8652 OHCI usb usb2: Manufacturer: Linux 2.6.30.9 ohci_hcd usb usb2: SerialNumber: rtl8652 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected usbcore: registered new interface driver usblp Initializing USB Mass Storage driver… usbcore: registered new interface driver usb-storage USB Mass Storage support registered. ——-8196D OTG init reg e0=99 reg e1=ac reg e2=98 reg e3=c1 reg e4=1 reg e5=89 reg e6=b8 reg e7=1d dwc_otg: version 2.60a 22-NOV-2006 [S0] lmdev=83b97b80 device_register :register pass =>probe
dwc_otg logicmodule: dwc_otg_driver_probe(83b97b80)
dwc_otg logicmodule: start=0xb8030000
[S2] otg_dev=83ba3a80
dwc_otg logicmodule: base=0xb8030000
dwc_otg logicmodule: otg_dev=0x83ba3a80
—-init hcd——
[S3] hcd==83b8e400
DWC_otg: Using DMA mode
dwc_otg logicmodule: DWC OTG Controller
dwc_otg logicmodule: new USB bus registered, assigned bus number 3
dwc_otg logicmodule: irq 15, io mem 0xb8030000
set OTG host to high speed !
DWC_otg: Init: Port Power? op_state=1
DWC_otg: Init: Power Port (0)
[USB] Device ‘DWC OTG Controller logicmodule’is plugged into port 3.
usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: DWC OTG Controller
usb usb3: Manufacturer: Linux 2.6.30.9 dwc_otg_hcd
usb usb3: SerialNumber: logicmodule
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
—-enable irq——
[S1] dwc_otg_driver, lmdriver=80443570
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 17
Bridge firewalling registered
Ebtables v2.0 registered
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
802.1Q VLAN Support v1.8 Ben Greear <[email protected]>
All bugs added by David S. Miller <[email protected]>
VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
Freeing unused kernel memory: 108k freed
sc_drv: module license ‘Sercomm’ taints kernel.
Disabling lock debugging due to kernel taint
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: port 1(eth0) entering forwarding state
device wlan0 entered promiscuous mode
[PHY_ConfigMACWithParaFile][MACPHY_REG_92C]
===> Load_92C_Firmware
= Load_92C_Firmware
br0: port 2(wlan0) entering learning state
Enter sc_fast_l2tp_init
#############DUMP MODULE FUNCTION ADDR########
sc_is_l2tp_device:c06ed01c
sc_event_ppp_dev_down:c06ed2f4
sc_l2tp_tx_id:c06ed4f8
sc_fast_l2tp_rx:c06ee658
get_fast_l2tp_lastxmit:c06ed05c
sc_check_for_fast_l2tp_to_wan:c06ed07c
sc_fast_l2tp_to_wan:c06edd90
MyQtL2tpCtrl:c06ed944
Insert quick routing module …
######DUMP QUICK TABLE FUNC ADDR#######
skb_dev_in_qtl:c06fd948
CheckSumModify:c06fd000
update_conntrack_time:c06fe004
matchFromLan:c06fdd3c
matchFromWan:c06fe040
doMatch:c06fe310
MyCheckSum:c06fd0bc
CheckSumDlt:c06fd10c
checkEntry:c06fd7e4
delEntry:c06fd348
addEntry:c06fd410
checkValidQTEntry:c06fd2b0
updateQtlWhenPktXmit:c06fd9c4
qtbl_read_proc:c06fe3dc
qtbl_write_proc:c06fe38c
######DUMP QUICK TABLE FUNC ADDR END#######
br0: port 2(wlan0) entering forwarding state
groupScore, ch 1,5: 5408
groupScore, ch 2,6: 7305
groupScore, ch 3,7: 8575
groupScore, ch 4,8: 6873
groupScore, ch 5,9: 3830
groupScore, ch 6,10: 4050
groupScore, ch 7,11: 3471
FAST-L2TP: call-reply, dev->name=eth1
##################proc config write##################
type:1
wan_dev_name:eth1
ppp_dev_name:
daddr: 5515d0c7
saddr: 0ac08197
tid: 19742
cid: 34299
dmac: 00:1c:f0:21:2a:82
smac: 00:0e:8f:3d:1d:65
#######################################################
plugin config wirte——————————————DUMP L2TP INFO —>BEGIN
wan dev: eth1
ppp dev: NULL
saddr: 0ac08197
daddr: 5515d0c7
tid: 19742
cid: 34299
mac: 00:1c:f0:21:2a:82 00:0e:8f:3d:1d:65
valid: 1
dropped packets 0
passed packets 0
pass fragment 0
state 2
DUMP L2TP INFO —>END
wlan0: A wireless client is associated — 02:03:7F:EC:54:8D
BIT(11) of 0xd2c = 1, 0xd2c = 0xcc979975
wlan0: WPA2-AES PSK authentication in progress…
wlan0: A wireless client is associated — 02:03:7F:EC:54:8D
wlan0: Open and authenticated
wlan0: A wireless client is associated — C0:4A:00:29:20:FE
BIT(11) of 0xd2c = 1, 0xd2c = 0xcc979975
wlan0: WPA2-AES PSK authentication in progress…
wlan0: A wireless client is associated — C0:4A:00:29:20:FE
wlan0: Open and authenticated
wlan0: Delete MC entry not found!
wlan0: Delete MC entry not found!
##################proc config write##################
type:0
wan_dev_name:
ppp_dev_name:
daddr: 00000000
saddr: 00000000
tid: 0
cid: 0
dmac: 00:44:08:04:7f:e6
smac: 00:00:00:00:00:00
#######################################################
DUMP L2TP INFO —>BEGIN
wan dev: NULL
ppp dev: NULL
saddr: 00000000
daddr: 00000000
tid: 0
cid: 0
mac: 00:00:00:00:00:00 00:00:00:00:00:00
valid: 0
dropped packets 0
passed packets 0
pass fragment 0
state 0
DUMP L2TP INFO —>END
FAST-L2TP: call-reply, dev->name=eth1
##################proc config write##################
type:1
wan_dev_name:eth1
ppp_dev_name:
daddr: 5515d0d8
saddr: 0ac08197
tid: 2744
cid: 1584
dmac: 00:1c:f0:21:2a:82
smac: 00:0e:8f:3d:1d:65
#######################################################
plugin config wirte——————————————DUMP L2TP INFO —>BEGIN
wan dev: eth1
ppp dev: NULL
saddr: 0ac08197
daddr: 5515d0d8
tid: 2744
cid: 1584
mac: 00:1c:f0:21:2a:82 00:0e:8f:3d:1d:65
valid: 1
dropped packets 0
passed packets 0
pass fragment 0
state 2
DUMP L2TP INFO —>END

[свернуть]

Также если кому интересно, список модулей ядра

Спойлер

networkmap 4784 1
quick_routing 534896 0
plugin_l2tp 12672 0
nf_nat_pptp 2608 0
nf_conntrack_pptp 6000 1 nf_nat_pptp
nf_nat_sip 7136 0
nf_conntrack_sip 18704 1 nf_nat_sip
sit 11472 0
ip6table_filter 2272 1
ip6t_LOG 7152 5
nf_conntrack_ipv6 13744 15
ip6t_REJECT 3952 0
ip6_tables 12624 2 ip6table_filter,ip6t_LOG
ipv6 269056 29 sit,nf_conntrack_ipv6,ip6t_REJECT
tunnel4 3344 1 sit
nf_nat_ftp 2816 0
nf_conntrack_ftp 7184 1 nf_nat_ftp
xt_CONNMARK 2576 0
nf_nat_h323 7008 0
nf_nat_rtsp 5200 0
nf_nat_proto_gre 2000 1 nf_nat_pptp
xt_tcpmss 1840 0
xt_state 1888 31
xt_phyport 1840 0
xt_mac 1408 0
xt_limit 2256 16
xt_length 1536 0
xt_iprange 2192 0
xt_dscp 2256 0
xt_TCPMSS 4256 2
xt_MARK 1952 0
nf_conntrack_rtsp 7216 1 nf_nat_rtsp
nf_conntrack_proto_gre 4848 1 nf_conntrack_pptp
xt_mark 1536 1
nf_conntrack_h323 48272 1 nf_nat_h323
ext4 236672 0
jbd2 57152 1 ext4
push_button 2864 0
led 5744 0
sc_drv 6192 0

[свернуть]

Схема разделов Beeline Smartbox: 1 комментарий

  1. Вот тут:
    http://forum.ixbt.com/topic.cgi?id=14:59612-8
    появилась инфа следующего содержания:

    » В прошивке 2.0.25 данные для входа суперадмина следующие:
    логин: SuperUser
    пароль: SFXXXXXXXXXX (серийный номер устройства)
    То есть теперь он у каждого роутера уникален. «

Добавить комментарий

Ваш e-mail не будет опубликован. Обязательные поля помечены *